Hydra Loc

Where is Hydra Loc used?

Hydra Loc is specifically formulated for use on:

  • Broom Finished Concrete
  • Concrete Older than 1970
  • Concrete with Water Seepage Problems
  • Poured Concrete Walls
  • Concrete with Exposed Aggregate

Hydra Loc is a silicate based concrete sealer that can be used anywhere you have concrete with a rough texture. It will greatly reduce vapor transmission which leads to flooring or paint release, as well as strengthening and conditioning your concrete. Hydra Loc can be used alone or in conjunction with our Poly Top Seal or NCS-2O Negative sealers.

Preparation

All concrete must be clean, raw concrete, no paint or sealers. To remove algae spray down with a 50/50 mixture of Clorox and tap water. Deck brush and hose or mop down to rinse. Allow area to semi dry and apply Hydra Loc with a inexpensive low-pressure (garden type) pump sprayer that you can use for both products.

Application Instructions

APPLICATION ON FLOORS
   
1. Floor must be damp before applying Hydra Loc. Use clean damp tap water to dampen.
2. Fill your sprayer with Hydra Loc and apply a wet application to the floors using a left- right and then up down motion for optimum coverage. Apply only enough product to create a shiny wet layer of sealer. Product will penetrate in 7 to 10 minutes. Do not let product puddle, mop up excess in low place after 10 minutes.
3. Apply 2 consecutive wet applications of Hydra Loc 30 to 45 minutes apart while floor is still damp from the previous application. Use a left-right motion to leave a shiny wet application of liquid sealer on the surface. Hydra Loc will penetrate the concrete surface in 7 to 10 minutes leaving just a damp looking surface. Reapply the second application while the surface is still damp for best results. A 3rd. application maybe applied for extra sealing strength if desired.
4. Use a deck brush and a liberal amount of water 6 to 12 hours after the last application, vigorously brush to remove all residual sealer and purged contaminates from all surfaces that are to be painted or have other coatings or adhesives applied.
5. Allow sealer 10 days to cure before applying paint or another topical treatment.
6. Allow product to cure the full 10 days before applying NCS-2O Negative.
7. Use a dry deck brush and vacuum to remove any purged lime or dust that may be on the surface before applying NCS-2O Negative.
8. Using the same clean sprayer apply NCS-2O Negative in a left to right and then a up down motion for complete coverage. Allow a maximum of 1 hour for NCS-2O Negative to begin it's curing process and then repeat a second application. Do not allow the product to puddle after 20 minutes, mop up excess from low spots.
9. After and between applications clean your sprayer with clean tap water, run pressurized water through the nozzle.

APPLICATION FOR WALLS
   
1. Fill your sprayer with Hydra Loc and apply a wet application to the walls spraying from the top down using a left right and then up down motion for optimum coverage. Apply only enough product so as not to create run-off of the Hydra Loc. A 12 inch sag in the sealer is maximum. Repeat the application within 30 to 45 minutes.
2. Apply 2 consecutive wet applications of Hydra Loc. 30 to 45 minutes apart while wall is still damp from the previous application. Use a left right, up down motion to leave a shiny wet application of liquid sealer on the surface. Hydra Loc. will penetrate the concrete surface in 5 to 10 minutes leaving just a damp looking surface. Reapply the second application while the surface is still damp for best results. A 3rd. application maybe applied for extra sealing strength if desired.
3. Use a deck brush and a liberal amount of water 6 to 12 hours after the last application, vigorously brush to remove all residual sealer and purged contaminates from all surfaces that are to be painted or have other coatings or adhesives applied.
4. Allow sealer 10 days to cure before applying paint or another topical treatment.
5. Allow product to cure the full 10 days before applying NCS-2O Negative.
6. Use a dry deck brush and vacuum to remove any purged lime or dust that may be on the surface before applying NCS-2O Negative.
7. Using the same clean sprayer apply NCS-2O Negative in a left to right and then a up down motion for complete coverage. Allow a maximum of 1 hour for NCS-2O Negative to begin it's curing process and then repeat a second application. Do not allow the product to puddle.
8. After and between applications clean your sprayer with clean tap water, run pressurized water through the nozzle.

Coverage Rates

Hydra Loc coverage rates will vary depending on the porosity of the concrete. The coverage can be greatly reduced with severe alkali disintegration. The coverage rates below are to be used as a guideline.

Expect one pail to cover two applications on 800 - 1000 square feet.

Expect one pail to cover three applications on 400 - 500 square feet.

Online Ordering
Site Map
This website was developed by www.LogicFlame.com
 
Concrete Sealants - Repair Epoxies - Cleaners - Coatings - Concrete Stains - Return Policy - Links - Webmail
Endur-O-Seal USA, Inc.
12502 Lazywood Lane
Pinehurst, Texas 77362 		Toll Free 1-800-259-8855
Office 1-281-356-5117
Fax 1-281-356-9332
For additional information please visit our former site at http://www.concretesealer.com

© 2001 - 2007 Endur-O-Seal USA, Inc. TM